Using a lighter to directly splice two pieces of 3D printer filament.

How to Splice Filament: Three Methods and Which Joint Holds

Written by: Enderwick Pei

|

Published on

|

Time to read 4 min

A spool runs out with 200 g left. A roll snaps in the middle of a long print. You have four partial spools of the same color and want one usable one. In all three cases the fix is the same: join two filament ends into a single continuous strand and keep printing.

Splicing is not difficult, but it is easy to do badly. A joint that is slightly too thick, slightly oval, or only partly fused will pass a hand pull test and still jam inside an AMS, a PTFE tube, or the extruder gears twenty minutes into a print. This guide covers the three methods that actually work, what each one gets right, and how to check a joint before you trust it.

What a usable joint has to do

Four things, in order of how often they go wrong.

Diameter. The welded section has to come out at the same nominal size as the rest of the strand, within a few hundredths of a millimeter. A joint that measures 1.9 mm on a 1.75 mm filament is a plug.

Roundness. Heat and pressure flatten filament easily. A flattened joint loses grip in the extruder gears even when it clears the tube.

Fusion. The two ends have to melt into one piece of polymer, not sit next to each other inside a sleeve. A cold joint looks fine and pulls apart under tension.

Length. A short joint passes through bends, hubs, and the AMS more easily than a long one.

Method 1: PTFE sleeve and heat

The oldest method, and still the reference point for the other two.

  1. Cut both filament ends square with flush cutters. An angled cut traps air and creates a weak spot.
  2. Slide a short piece of PTFE tube over one end. The tube's inner diameter should be just large enough to accept the filament, because the tube is what keeps the joint round while it cools.
  3. Push the two ends together inside the tube so they meet with light contact.
  4. Apply heat to the tube until the filament inside softens and the two ends merge. A heat gun, a hot air rework station, or a dedicated splicer all work. A lighter also works, and is the fastest way to scorch the polymer.
  5. Let it cool completely before touching it. Warm filament deforms under almost no load.
  6. Slide the tube off, then trim the flash with flush cutters or a trim jig.

The tube does the alignment. That is the whole trick, and it is why this method is reliable with almost no equipment.

Using a lighter to directly splice two pieces of 3D printer filament.

Method 2: A dedicated filament splicer

A dedicated tool puts the alignment channel, the sleeve guide, and the heat source in one body, so the two variables you were controlling by hand are now fixed. Feed both ends in, close the tool, wait for the heat cycle, pull the finished joint out, trim it.


The gain is repeatability rather than a better theoretical joint. If you splice once a month, the sleeve and heat gun method costs less and works fine. If you are combining partial spools regularly, or running several printers, fixed geometry is what stops the occasional fat joint from turning into an AMS jam.

Method 3: Jig, tape, and a soldering iron

Printed jigs and V-groove blocks with a soldering iron are popular because they cost nothing and the files are everywhere. They can produce a good joint, but every variable is back in your hands: how the two ends are held, how much heat reaches the polymer, how long you hold it, and how hard you press. Expect to scrap the first few attempts while you learn what a good joint feels like.

The failure mode is consistent. The joint looks fused, measures slightly wide at the seam, and survives a pull test. Then it reaches the AMS.

Scraping away excess melted filament from the splice with a small knife

Trimming and checking before you print

Do not skip this step. After the joint cools:

  • Trim the flash flush. Any raised ring is a future jam.
  • Measure the joint with calipers at two angles, 90 degrees apart. It should match the filament's nominal diameter as closely as you can get it, and it should not be oval.
  • Bend the joint gently. It should flex like the rest of the strand. A joint that creaks or shows a visible seam is not fused through.
  • Pull it. A good weld holds under a firm steady pull. A bad one separates with a soft pop.

Which materials splice cleanly

PLA, PETG, ABS, and ASA weld into usable joints with a little practice. TPU is difficult because the material deforms before it fuses and the joint rarely stays round. Fiber-filled filaments such as carbon fiber or glass fiber blends are the hardest case: the fibers do not fuse across the joint, so the weld is mechanically weak even when it looks clean.

Never splice two different materials. PLA and PETG do not bond, and the joint will separate under load regardless of how well you heat it.

Where not to put a joint

Keep joints out of the last section of filament before the extruder if you can, and avoid leaving one parked in a retraction-heavy path. If a joint has to pass through the AMS, it needs to be as close to nominal diameter as you can measure. On a visible outer wall, plan the joint for a spot that will not show, or splice before the print rather than during it.

Can you splice PLA to PETG?

No. The two polymers do not fuse. The joint will look joined and separate under tension.

How strong is a spliced joint?

Strong enough to feed and print, weaker than virgin filament. Treat it as a stress point and keep it away from visible surfaces.

Does a spliced joint break inside the AMS?

Only if it is oversized, oval, or badly fused. A trimmed joint at nominal diameter passes through the same path as normal filament.

Do I need a PTFE sleeve?

For the sleeve-and-heat method, yes. The tube is what keeps the joint round while it cools.

Can I splice TPU?

It is possible and rarely worth it. The material deforms before it fuses, and the joint usually ends up out of round.